Fuhr Industrial

195 can be used for glazing and highlighting sealed wood surfaces. It can be used to achieve the “antique” and/or “distressed” look on kitchen cabinets, furniture, and millwork. 195 is suitable for either interior or exterior applications. It can be applied by rag, brush or spray. Five standard colors are available including Black, White, Raw Umber, Chocolate, and Coffee. Application Method 1. Prep. Sand
180-220 grit Aluminum Oxide Sand paper

2. Stain (optional)
Apply according to product specifications.

3. Seal
Apply according to product specifications.

4. Glaze
Apply Fuhr Glaze with a brush or rag very liberally over the surface to be glazed. Remove the glaze with a clean bleached cotton cloth.

5. Topcoat
Apply according to product specifications.

Sprayable Paste Wood Grain Filler, 175 is a high solids, clear acrylic grain filler supplied in a sprayable viscosity for application by spray or hand. For use on open-grained woods to fill the grain to provide a smooth, un-textured appearance to the final finish once topcoats are applied. Supplied in clear, 175 allows for filling and grain definition without altering the color of the wood. The fast drying
nature of this product allows staining and top-coating in as little as two hours with Fuhr’s finishing systems. Application Method 1.Prep. Sand
150-220 grit Aluminum Oxide Sand paper

2. Grain Filling
Applied to bare wood by brush or spray and the excess product should be
“removed” off using a rubber or plastic scraper. 3. Sand
Sand the filled surface with 180-220 grit Aluminum Oxide Sand paper leaving
filler in the grain, and the bare wood exposed.

4. Stain(optional)
Apply the stain according to product specifications.

5. Seal and Topcoat
Apply the sealer and/or topcoat according to product specifications.

Aluminum Oxide Modified Urethane is a 33% solids uniquely formulated water based urethane floor finish designed to replace conventional oil modified urethane finishes. 855 has been enhanced with Aluminum Oxide for extended abrasion resistance and longevity. This product meets KCMA standards and is rated for interior or exterior use. Application Method 1. Prep. Sand
150-180 grit Aluminum Oxide Sand paper

2. Stain (Optional)
Apply according to product specifications.

3. Seal
Apply 3-5 wet mils of 855 as a seal coat to the dried stained surface.

4. Sanding
Allow 855 to dry completely, and thoroughly sand with 180-220 grit Aluminum Oxide Sand paper

5. Topcoat
Apply 3-5 wet mils of 855. Repeat steps 4 and 5 for additional build and protection.

Enhanced Flow Additive, 123 is designed for use when the woodworker desires to thin the product for easier flow out. This product will extend the open time slightly, and provide better flow and leveling characteristics in the material. 123 is to be used in the high solids primers and 9100 series products. Application Method 1. Shake
Shake the container thoroughly before using.

2. Addition
Incorporate up to 5% (6 Oz. per Gallon) into the primer or finish product.

3. Mixing
Do Not Shake, stir product 123 into the primer or finish product for proper incorporation.

4. Specifications
Incorporation of 123 into a primer or coating at maximum dosage levels will result in a change in VOC. This change will add approximately 23 grams per liter total VOC.

Stain Retarder, 125 is designed to slow down the drying time in waterbased stains as well as clear finishes. This product is recommended for particularly dry and/or hot environments. Application Method 1. Shake
Shake the container thoroughly before using.

2. Addition
Incorporate up to 5% (6 Oz. per Gallon) into the stain or finish product.

3. Mixing
Do Not Shake, stir product 125 into the stain or finish product for proper incorporation.

4. Specifications
Incorporation of 125 into a stain or coating at maximum dosage levels will result in a change in VOC. This change will add approximately 49 grams per liter total VOC.

Universal Cleaner is non-flammable, biodegradable cleaner expressly created for use in the wood finishing industry. It rapidly removes urethanes, acrylics and other difficult to remove paints and clear sealer products from wood cabinets and most other wood surfaces. 330 Universal Cleaner is an excellent choice for cleaning laminates of overspray. It can also be used as a general purpose cleaner and degreaser for cleaning machinery, floors and other general cleaning tasks. Application Method 1. As a stripper
Apply 330 liberally, and allow it to penetrate for 20 minutes.

2. Removal
Using the proper removal tools, remove 330 from the surface.

3. Neutralize
Neutralize the surface with a blend of water and vinegar using a rinse type method.

4. As a cleaner
Reduce the 330 cleaner with water 6 parts water to 1 part 330. This can be used as an equipment cleaner.

5. Removal
Flush all equipment well with water and always check material for contamination before usage. Follow step 3 to properly neutralize the equipment.