Multitek
700 Main Street, Po Box 170, Prentice, Wi 54556-0170
Prentice, Wisconsin-545560170, USA
Next Product

Grapples & Attachments

TIME SAVING…Hauls loads of brush in minutes.
BACK SAVING…Feed large capacity chippers safely.
MONEY SAVING…The Mark II Grapple System will pay for itself in the first month.

Tree work, landscaping and construction is tough, backbreaking, and grueling work. If you are tired of trying to find the right grapple attachment for the right job, or for the right price? If tree service, landscaping or construction is your business and you're interested in boosting your productivity by 50% while reducing the risk of injury to your crew, have we got a piece of rugged equipment for you! Material handling is not an issue anymore, hauling loads of brush to the chipper takes minutes instead of hours. What would take 3 men 45 minutes, now takes one man 5 minutes. Hauling brush by hand and feeding a chipper can cause injuries. If you don't have a high capacity chipper now, you will have one after you own a Multitek MARK II attachment featuring a 360 Degree Rotating Grapple / Winch / Pushbar System for Skidsteer Loaders.

Grapples & Attachments

The LCR-60 Land Clearing Rake is a unique attachment used for general land clearing or cleaning right of ways. The hardened steel teeth allow the operator to quickly & efficently grub and gather brush, small stumps, rocks and push material into a pile. The landclearing rake's 13 teeth are bi-directional which allow the machine to work in both directions pushing and pulling. This allows you to clear along fence lines, buildings and other objects. By lifting the rake the machine operator can then straddle and move larger rocks inside the rake frame. Multitek manufacturing uses a standard two pin quick attachment plate that is widely accepted in the market. The attachments are factory tested and ready to go to work.

  • Width: 59 ” (150 cm)
  • Fork Length: 66 ” (168 cm)
  • Height: 38 " (96 cm)
  • Quick-Tach Plate ¼ ” (.64 cm)
  • Weight: 490 lbs (222 kg)
Grapples & Attachments

The LF-150 Log Fork an economical, lightweight grapple attachment featuring tandem fork tines with a single hydraulic cylinder powering the center clamp. Multitek manufacturing uses hardened bushings and grease zerks at the pivot points and a standard two pin quick attachment plate that is widely accepted in the market. Atttachments come equipped standard with 1/2" Pioneer hydraulic quick connects and Weatherhead hydraulic hose and fittings. The attachments are factory tested and ready to go to work. Grapples will require auxiliary hydraulic system on loader and hydraulic hoses to go from loader to grapple.

  • Grab Opening: 34 ” (86.4 cm)
  • Grab Close: 3.5 ” (9 cm)
  • Width: 44 ½ ” (113 cm)
  • Height: 28” (71 cm)
  • Fork Length: 22 ½ ” (57.2 cm) tapered standard
  • Weight: 440 lbs (200 kg)
  • Quick-Tach Plate ¼ ” (.64 cm)
  • Quick Connects: ½ ” (1.28 cm) Pioneer standard
Grapples & Attachments

New adjustable pin mount allows skidsteer loader operators the choice to convert the Multitek Model LF-175 Log and Brush Fork clamp position, depending on the specialized task at hand. By positioning the pin location forward, for smaller diameter logs, poles or pipe sections, it will allow the clamp to by-pass through the plane of the forks to clamp tight. Moving the pin to the back position will allow the clamp a bigger grab opening for handling bulky loose material, such as brush and branches. The LF-175 Log and Brush Fork attachments come equipped standard with hydraulic quick connects and Weatherhead hydraulic hose and fittings. This LF-175 Log & Brush Fork will require an auxiliary hydraulic system on loader and hydraulic hoses to go from loader to grapple. Multitek manufacturing uses brass bushings and grease zerks at the pivot points and a standard two pin quick attachment plate that is widely accepted in the market. For further info on quality skidsteer log and brush grapple attachments call 800-243-5438.

Grapples & Attachments

The Multitek Model LG-200 Log Grapple attachment work well for sorting and moving logs in the forest or mill yard. Powerful hydraulic cylinders drive the heavy duty pivoting double jaw clamp over each curved and tapered fork tine, giving you the necessary gripping power. The hydraulic cylinders are mounted inside the grapple main frame to help protect them during severe duty operating conditions. Grapples will require auxiliary hydraulic system on loader and hydraulic hoses to go from loader to grapple.

  • Grab Close: 5 ” (12.7cm)
  • Width: 44 ” (112 cm)
  • Grab Open: 25 ” (63.5 cm)
  • Quick-Tach Plate: ¼ ” (.64 cm)
  • Weight: 520 lbs (236 kg)
  • Jaw Ram Cylinder: 2 ” i.d (5 cm)
  • Grapple Jaw: ¾ ” Steel Burnout (1.9 cm)
  • Grapple Side Plates: ¼ ” Welded Box (.64 cm)
  • Quick Connects: ½ ” Pioneer (standard) (1.28 cm)
Grapples & Attachments

The LG-275 Log Grapple is recommended for the new generation of higher horsepower skid steer loaders. Multitek manufacturing uses hardened bushings and grease zerks at the critical pivot points and a standard two pin quick attachment plate that is widely accepted in the market. Grapple attachments come equipped standard with 1/2" Pioneer hydraulic quick connects and Weatherhead hydraulic hose and fittings. The attachments are factory tested and ready to go to work. Grapples will require auxiliary hydraulic system on loader and hydraulic hoses to go from loader to grapple.

  • Grab Open: 44 ” (112 cm)
  • Width: 49 ” (124 cm)
  • Grab Close: 6 ” (15.2 cm)
  • Weight: 980 lbs (444 kg)
  • Grapple Side Plates: ¼ ” (.64 cm) Welded Box
  • Grapple Jaw: ¾ (1.9 cm) Steel Burnout
  • Jaw Ram Cylinder: 2 ½ ” (6.4 cm) bore
  • Quick-Tach Plate: 3/8 ” (.95 cm)
  • Quick Connects: ½ ” (1.28 cm) Pioneer (standard)
Grapples & Attachments

The MG-6419 Multigrapple is used for large diameter clamping tasks and has non-adjustable width forks. This versatile grapple attachment features our largest grapple opening at 64" inch gripping diameter Multitek manufacturing uses hardened bushings and grease zerks at the pivot points and a standard two pin quick attachment plate that is widely accepted in the market. Attachments come equipped standard with 1/2" Pioneer hydraulic quick connects and Weatherhead hydraulic hose and fittings. The attachments are factory tested and ready to go to work. Grapples will require auxiliary hydraulic system on loader and hydraulic hoses to go from loader to grapple.

  • Grab Opening: 64 ” (162.5 cm)
  • Grab Close: 20 ” (50.8 cm)
  • Grab Width: 6 ¾ ” (17cm) (center jaw)
  • Grapple Height: 36 ” (91.4 cm)
  • Grapple Width: 44 1/2 ” (113 cm)
  • Fork Length: 40 ” (102 cm) tapered (standard)
  • Weight: 620lbs (310 kg)
  • Quick-Tach Plate ¼ ” (.64 cm) (standard)
  • Quick Connects: ½ ” (1.28 cm) Pioneer (standard)
Grapples & Attachments

The UG-6420 Utility Grapple is used for large diameter clamping tasks where adjustable forks are needed. This grapple features adjustable forks to 50" in width. This utility grapple attachment features a huge grapple opening at 64" gripping diameter. Multitek manufacturing uses hardened bushings and grease zerks at the pivot points and a standard two pin quick attachment plate that is widely accepted in the market. Attachements come equpped standard with 1/2" Pioneer hydraulic quick connects and Weatherhead hydraulic hose and fittings. The attachements are factory tested and ready to go to work. Grapples will require auxiliary hydraulic system on loader and hydraulic hoses to go from loader to grapple.

  • Grab Opening: 64 ” (162.5)
  • Grab Close: 20 ” (50.8 cm)
  • Grab Width: 6 ¾ ” (17 cm) center jaw
  • Grapple Height: 38 ¾ ” (98.4 cm)
  • Grapple Width: 44 ½ ” (113 cm)
  • Fork Length: 48 ” (121.9 cm) tapered standard
  • Weight: 845 lbs (384 kg)
  • Quick-Tach Plate: ¼ ” (.64 cm)
  • Quick Connects: ½ ” (1.28 cm) Pioneer standard
Grapples & Attachments

Easily cut, split, and quarter the most difficult of oversize large diameter log rounds with the Multitek SuperAX Skid Steer Splitter. With 35 tons of crushing force and a fast 10 second cycle time, the SuperAx will effortlessly break down oversize log rounds into manageable pieces for your operation. Whether its log yard cleanup or firewood preparation, the SuperAX makes processing logs a breeze.

The Skid Steer SuperAX is designed to fit easily on most skid steer attachment mounting plates. Mounted in the front for easy viewing and operation, the machine's unique parallel design for splitting wood will make every ones job safer and easier trying to split large diameter logs or blocks of wood. You never have to handle the large diameter blocks of wood by hand again. Let the SuperAX do the backbreaking work for you without having to touch the block of wood ever.

Send Enquiry
Your Contact Details




 
 
 
 
 
 
 

sending enquiry
Thank You

unable to instantiate your call right now. please try after some time.

close

© Copyright HelloTrade.com
Home | About Us | Partner with us | Disclaimer | Testimonial | Feedback & Complaint | Help